Sta Green Spreader Setting For Scotts Turf Builder

Cross referencing it over to a Scotts EdgeGuard DLX would be a spreader setting of 6 see below. You can also find spreader settings on our product information pages Lawn Food Grass Seed Weed Control and Insect Grub Disease Control.

Sta Green Broadcast Lawn Spreader Review Youtube

If your spreader is not listed for the selected product we have provided a generic setting chart for your convenience.

Sta green spreader setting for scotts turf builder. Improper spreader settings can lead to a waste of time and money if too much product is used and callbacks from customers if too little product is dispersed. The Scotts spreaders will work with other brands of lawn care products but the specific settings may vary. Select Product Spreader.

The Scotts Green Max Rate is for springsummer only. They call for a 125 setting and 2. Setting Broadcast Spreaders 4 5 55 6 Insecticide Diazinon 2 Setting Broadcast 35 Grass Seed Blue Grass Bent Grass Fine Mixture Coarse Seed Rye Fescue Bermuda 3 3 10 10 Calibration Indicator Button Setting Numbers Control Lever 10-6-4 Weed Feed 18-22-6 Starter Winterizer 20-10-5 Turf Food 22-3-11 Crabgrass Preventer Plus 25-3-3 Weed 7 Feed 2Triamine 26-3-3 Turf Food Agway.

If your spreader is not listed for the selected product we have provided a generic setting chart for your convenience. Set spreader at 14 to 13 of the dial as a starting point. Always calibrate your spreader.

Spreader settings are correct at time of publication. Precision Green PF-4 Scotts Speedy Green 1000 Scotts old Plant Mate Scotts Speedy Green 2000 Taylor Scotts Speedy Green 3000 Scotts old Plant Mate Taylor Tru Temper Spreader Name Spreader Name Residential Spreader Settings 4 Spreader Not Listed - Setting Tip. It may take a few passes.

Spreader settings can be found on the Details Usage tab on the product information. Use the Regular Feed Rate in the fall. Regular Feed Rate Scotts hand-held spreader - Setting 4-12 Scotts drop spreader - Setting 10-12 Scotts Wizz spreader - Setting 4-12 Scotts broadcastrotary spreader - Setting 4-34 Scotts Elite Spreader - Setting.

Make sure you sweep up. Place enough material in the hopper to cover 1000 square feet. For application using a pushed broadcast spreader Scotts recommends a setting of 5 12 when overseeding and a bare-lawn setting of 8 14.

Adjust the setting as necessary to spread the product evenly over the entire area. Open the hopper as you cross the start line and close it. 124 rows Referring to the list above find a rotary or drop spreader depending upon which one you.

Select Product Spreader. Determining Spreader Settings. Place your spreader setting on a low setting usually one-fourth of the spreader setting range or less.

Turf grass grows best with a soil pH between 60 and 70slightly acidic to neutral. If you cant find setting information for your model calibrate the model by measuring fertilizer to cover 100 square feet according to package directions. Test your soils pH level before using any lime.

Fill the spreader with the amount of fertilizer or seed necessary to cover your lawn and then push it along the marked course. These are approximate settings. If there is material left over increase your setting.

2 and distribute the product over the measured area. Scotts sometimes claim that their form of slow-release is better than sulfur coated nitrogen of the second tier brands. Dimension 10 19-0-6 has a LESCO spreader setting of 15.

Scotts sun and shade seed mix is designed to stay green in extreme heat and in full sun to dense shade conditions. When using a LESCO product find the designated setting listed on the bag and then. 2-4 select the lower setting eg.

You can skip the lime unless your soil has a pH below 60. Cover the area with a tarp and mark the start and finish line on the tarp with masking tape. What setting should we use with a Scotts Turf Builder Classic Drop Spreader.

Stagreen probably uses dithiopyr crabgrass control. Please keep in mind that labeled settings on the product bag and those listed below are approximate and should be. Set the spreader on low and spread.

Use our easy-to-use spreader settings table below to set Scotts and EverGreen spreaders correctly when using our products. Spread the material over a 50 x 20-foot area 1000 square feet. Scotts Wizz spreader - Setting 5 Scotts broadcastrotary spreader - Setting 5-14 Scotts Elite Spreader - Setting 5-14.

Always read instructions before use. To get spreader settings for our product and your spreader please select from the options below and click Get Spreader Settings. To determine the appropriate rates of application and spreader settings for your product and spreader please select from the options below and click Get Spreader Settings.

How to Find Spreader Settings. A Guide to Lawn Care Spreader Settings The following table has been provided by Scotts to show the correct settings for optimal use of the fertlisers seed and sand. This is just a guide always calibrate spreader.

Always ensure spreader is within calibration. As the name implies Turf Builder Sun Shade is a general-purpose turf blend suitable for a variety of growing conditions. I am not sure if Scotts is using Pendimethalin or has changed to Tenacity mesotrione active ingredient in their Halts product.

If you use their drop spreader Scotts recommends a setting of 8 12 for overseeding and 12 12 for a new lawn. Set a Scotts rotary spreader to 5 12 for overseeding and 8 14 for a new lawn. Spreader settings for Scotts Lawn Care products can be found on the product package.

If your product provides a range for your spreader setting eg. Starting with the appropriate setting for your specific machine will help. If you come up short decrease your setting.

The company we by the fertilizer from ZAMZ0WS in Boise ID provides us with bags of fertilizer calibrated for the Scotts Accugreen 3000 spreader. Age and condition of spreader can affect setting.

Spreader Settings Dayton Nursery